This Machine is in our Shop at New Hartford, CT 06057
It will sell to the High Bidder Regardless of Price.
There is NO RESERVE PRICE.
GENUINE BRIDGEPORT SERIES 1
TWO HORSEPOWER
(2HP) VARIABLE SPEED
PREMIUM QUALITY
by BRIDGEPORT
KNEE MILL
CLICK HERE TO SEE THE CATALOGUE DESCRIPTION OF THE
SERIES 1 BR2J BRIDGEPORT AS WELL AS TECHNICAL SPECIFICATIONS
CLICK HERE TO SEE BRIDGEPORT SERIES 1 FEATURES
CLICK HERE TO SEE ADDITIONAL TECHNICAL SPECIFICATIONS
(Head Serial Number J-237857 / Machine Serial Number 12BR220780)
POWERFUL TWO HORSEPOWER (2 HP) 2J Head with Bridgeport R8 Spindle Taper
CLICK HERE TO SEE THE BRIDGEPORT
CATALOGUE DESCRIPTION OF THE BRIDGEPORT 2J HEAD
42" LONG TABLE
CHROMED KNEE
BRAND NEW POWER TABLE FEED
TWO NEW POWER KNEE FEEDS
BRIDGEPORT MILLER
6" GENUINE BRIDGEPORT
SWIVEL BASE VISE
WITH HANDLE
and HARD JAWS
BRAND NEW GENUINE FAGOR DRO WITH LARGE ADJUSTABLE MOUNTING BRACKET
R-8 BRIDGEPORT TOOLING
HOLD DOWN KIT INCLUDED
This Bridgeport is in Nice Condition. It recently was examined and tuned up.
Knee & Table have about 0.016" and 0.012" Feed Screw Backlash.
Machine and Accessories all work well and do their jobs fine.
Table Surface has a smattering of drill points, wrench dings and scratches
and possibly a couple of minor miscuts: Nothing that impacts usefulness.
Quill Feeds Up & Down work fine.
Speed Range 60-4200RPM Achieved through
Back Gear & Crank-Operated Variable Speed Drive
Motor marked for 220/230/440/460 Volts Three Phase. It runs fine on 230Volts Here.
KURT POWERLOCK, PNEUMATIC POWER DRAWBAR:
The Machine Comes with Newly Installed Kurt POWER LOCK Drawbar. The Power Lock Draw Bar Is Pneumatically actuated and will conveniently hook into your shop's own air supply. Being Pneumatic It delivers consistent torque on the draw bar, there by reducing strain placed on the drawbar.
This Power Drawbar Allows for Quick Tooling Changes. Taking only 1/4 of the time normally necessary to change tooling. This alone Can Dramatically Increase the Efficiency of Your Operation. 
This Kurt POWER LOCK Comes With A Simple Push Button Control Mounted on the Head, Thus Reducing Strain On the Operator, As Well As Saving Time.
BRAND NEW GENUINE FAGOR DIGITAL READOUT FOR TABLE & KNEE:This Bridgeport Milling Machine has a BRAND NEW GENUINE FAGOR DIGITAL READOUT FOR TABLE & KNEE WITH LARGE ADJUSTABLE MOUNTING BRACKET as shown in the pictures.
NEW POWER TABLE FEED:This Bridgeport Milling Machine has a BRAND NEW Power Table Feed with Feed Stops and Switches as shown in the pictures.
POWER UP-DOWN & IN-OUT KNEE FEEDS: We are also Including BRAND NEW Power Knee Feeds for Both Up-Down and In-Out Axes with Rapid Traverse and a NEW Electronic Limit Switch and Dogs for Auto Feed Shut Off!
BIJUR ONE-SHOT WAY LUBRICATION: Machine is Supplied with a BIJUR ONE-SHOT WAY LUBRICATION SYSTEM WITH RESERVOIR, PIPING and PUMP.
6" GENUINE BRIDGEPORT SWIVEL BASE VISE: Machine is Supplied with a 6" Wide Genuine BRIDGEPORT SWIVEL BASE VISE, Hard Jaws, Vise Handle, and the Tee-Nuts & Bolts to hold it down.
R-8 TOOLING & COLLET RACK: We are also Including 12 pieces of R-8 Tooling, Including a Brand New (1/32"-5/8" Capacity) Keyless Drill Chuck on R-8 Shank and the following (11) R-8 Collets:
1/8", 3/16", 1/4", 5/16", 3/8", 7/16", 1/2", 9/16", 5/8", 11/16" and 3/4".
HOLD DOWN SET: Machine is Supplied with a Brand New Hold Down Set with Tee Nuts, Clamps, Studs and Nuts as shown in the pictures.
CUTTING TOOLS: We are also Including an assortment of Cutting Tools to allow the Buyer to get started cutting right away.
(TOOLS SHOWN ARE REPRESENTATIVE ONLY. ACTUAL TOOLS MAY DIFFER)
SINGLE PHASE USE:Machine can be Operated in Areas without Three Phase Power by using a "Single Phase to Three Phase Converter" of Adequate Size. Be Careful. Improper Phase Converter that makes Bad Three Phase or Incorrect Wiring can result in Burnt Out Motor Coils. We cannot warrant against Motor Burn Out due to Bad Electrical Hook Up by Buyer.
If Buyer wishes, We can provide and Wire In a New Mitsubishi Inverter Drive Unit for $600.00 that will accept Single Phase 220 Volts Electricity and will Output Perfect Variable Frequency Three Phase 220 Volt Power to run this Machine with Variable Speed Throughout its Range.
DELIVERY INFORMATION
Buyer Pays Transportation Cost
We Cheerfully Arrange Winner's Trucking
Including On Request
Hydraulic Tailgate Delivery Service
Bridgeport will be loaded bare on a flat bed for $75.00.
Buyers can get online "Boxed Freight" Trucking Quotes from most major trucklines. Trucklines won't pay for damage unless Machine is boxed in. Use Class 85. Properly Skidded this Bridgeport & Accessories will weigh about 2400 Lbs. Shipping Box Dimensions are 68" Long x 56" Wide x 78" High. There will be a $250.00 Shipment Preparation Charge covering Skidding, Boxing, and Loading on a Commercial LTL Truck, if desired.
Our Zip is 06057 and we have daily pick-up service by several major carriers who can offer hydraulic tailgate delivery service. Try the following links:
CLICK HERE FOR FREIGHTQUOTE.COM (requires registration)
CLICK HERE FOR ABF FREIGHT QUOTE
CLICK HERE FOR ROADWAY FREIGHT QUOTE
NO RESERVE
We accept Online Payments through Paypal
American Express, Discover, Visa and MasterCard accepted Only through Paypal.com.
These items are surplus to the manufacturing needs of our
custom gear & aircraft part manufacturing operation:
Perry Technology Corporation - The Gear & Spline Experts
Click here to view my other auctions.
Connecticut buyers should include tax on Taxable items or supply properly completed Exemption forms.
Copyright 2001-2008. All text, pictures and descriptions are the property of Perry Technology Corporation
and may not be duplicated, copied or reproduced in any way without specific authorization of Perry Technology Corporation.
|